BZCPY - POURABLE SEALER S-10 PART A
- MSDS: BZCPY
- Manufacturer: FIRESTONE BUILDING PRODUCTS CO
- Product Name: POURABLE SEALER S-10 PART A
- National Stock Number: 8030-00F047275
Product Identification
Product ID:POURABLE SEALER S-10 PART A
MSDS Date:04/09/1995
FSC:8030
NIIN:00F047275
Kit Part:Y
MSDS Number: BZCPY
Responsible Party
CARMEL, IN 46032-5000
US
Emergency Phone: 615-231-3911/317-575-7190
Info Phone: 615-231-3911/317-575-7190
Cage: FIRES
Contractor
Telephone: 615-231-3911
Cage: FIRES
Ingredients
POLYOL
Fraction By Weight: 40-65%
CALCIUM CARBONATE, DOMOLITE, LIMESTONE, WHITING *96-1*
CAS: 1317-65-3
RTECS: EV9580000
Fraction By Weight: 30-45%
ACGIH TLV: 10 MG/CUM (DUST)
AMORPHOUS SILICA, AMORPHOUS-DIATOMACEOUS EARTH
CAS: 61790-53-2
RTECS: HL8600000
Fraction By Weight: 3-12%
ACGIH TLV: 10 MG/CUM DUST
POLYBUTENE
Fraction By Weight: 1-10%
Hazards
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:MAY CAUSE MINOR TEMPORARY
EYE/RESPIRATORY SYSTEM IRRITATION. MAY CAUSE SKIN IRRITATION IF THE
SKIN IS SCRATCHED/CUT.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:MAY CAUSE MINOR TEMPORARY EYE/RESPIRATORY
SYSTEM IRRITATION. MAY CAUSE SKIN IRRITATION IF THE SKIN IS
SCRATCHED/CUT.
First Aid
First Aid:EYES: FLUSH IMMEDIATELY W/GENTLE STREAM OF WATER FOR 15 MINS.
SKIN: WASH THOROUGHLY W/SOAP & WATER. INHALATION: REMOVE TO FRESH
AIR. INGESTION: DON'T INDUCE VOMITING. OBTAIN MEDICAL ATTENTION IN
ALL C ASES. NOTE: THE MIXTURE OF PARTS A & B MUST BE IMMEDIATELY
REMOVED FROM THE SKIN USING ACETONE.
Fire Fighting
Flash Point Method:TCC
Flash Point:365F
Extinguishing Media:WATER FOG, FOAM, CO2/DRY CHEMICAL
Fire Fighting Procedures:WEAR IMPERMEABLE PROTECTIVE CLOTHING & SELF
CONTAINED BREATHING APPARATUS.
Unusual Fire/Explosion Hazard:HEAT FROM FIRE CAN GENERATE FLAMMABLE
VAPOR & TOXIC FUMES. VAPORS >AIR, MAY TRAVEL LONG DISTANCES ALONG
THE GROUND IGNITE & FLASHBACK. (SEE SUPP)
Accidental Release
Spill Release Procedures:WEAR RUBBER BOOTS, GLOVES, APRON & SCBA IN THE
PRESSURE DEMAND MODE/A SUPPLIED-AIR RESPIRATOR. SMALL: EXTINGUISH
IGNITION SOURCES & ENSURE HANDLING EQUIPMENT IS ELECTRICALLY
GROUNDED. MOP/WIPE UP & DI SPOSE OF IN DOT-APPROVED WASTE
CONTAINER.(SEE SUPP
Handling
Handling and Storage Precautions:STORE IN A COOL, DRY AREA AWAY FROM
DIRECT HEAT. KEEP CONTAINERS TIGHTLY CLOSED WHEN NOT IN USE.
Other Precautions:FINE SPRAYS/MISTS MAY BE COMBUSTIBLE AT ROOM TEMPS
Exposure Controls
Respiratory Protection:NO SPECIAL REQUIREMENTS ARE EXPECTED UNDER
NORMAL CONDITIONS & USE.
Ventilation:REQUIRED
Protective Gloves:CHEMICAL RESISTANT
Eye Protection:SAFETY GLASSES/CHEMICAL SPLASH GOGGLES
Other Protective Equipment:IMPERVIOUS CLOTHING & BOOTS IF APPROPRIATE.
WEAR EYE/SKIN PROTECTIVE EQUIPMENT WHEN POURING, MIXING/APPLYING
MATERIAL.
Supplemental Safety and Health
Chemical Properties
Vapor Pres:0
Spec Gravity:1.288
Solubility in Water:SLIGHT
Appearance and Odor:LIGHT GRAY, VISCOUS LIQUID W/MILD ODOR
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS, ACID & BASES, PHOSPHORUS
Stability Condition to Avoid:HEAT, TEMPS
BUTADIENE
Disposal
Waste Disposal Methods:DISPOSE OF IN ACCORDANCE W/LOCAL, STATE &
FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.